Index of /images/scimages/1135

• Parent Directory
• 100_1077.JPG
• 100_1806.JPG
• 100_1838.JPG
• 100_1849.JPG
• 100_2226.jpg
• 12_coil_stator.JPG
• 12_coil_stator_2.JPG
• 12_coils_in_stator_mold.jpg
• 14_inch_x_.25_thick_plate.JPG
• 17__mold_curing.jpg
• 17_stator_with_coils_ready_for_glass.jpg
• 1st_homeade_genny_flying_in_northern_ontario.jpg
• 20_inch_stator_fresh_from_mold.jpg
• 20_inch_stator_painted.JPG
• 20_inch_stator_unpainted_2.jpg
• 2nd_genny_front.jpg
• 3_inch_magnets_on_rotor.jpg
• 4_coils_in_series___4_ohms.JPG
• 7_completed_ebay_solar_panels.jpg
• Alton_s_Wind_Calculations_Page.htm
• Blades_a_turning.jpg
• First_view_of_Genny_Making_Power.jpg
• Genny_at_sunset_of_first_night.jpg
• Homebuilt_Genny_Enjoying_Northern_Ontario_Sunset.jpg
• Inverter_Cable_Sizing_Chart.doc
• Inverter_FAQ___DonRowe_com___Frequently_Asked_Questions_about_Power_Inverters.htm
• Moose_at_Hough_Lake_Boat_Ramp.jpg
• Voltage_Drop_Calculator.htm
• WNDMILL_may_26th_in_city.jpg
• alignment_mark_on_each_rotor.jpg
• another_view_of_the_wind_genny.jpg
• basic_coil_winding.JPG
• battery_bank_hooked_up
• battery_chapter.pdf
• blade_root_as_per_hughs_book.jpg
• bottom_off_stator_mould.jpg
• bracket_closeup_welded_and_lag_bolt_city.jpg
• cemented_tower_base_finished
• closeup_of_hughes_blade_root.jpg
• coil_and_stator_paper_template
• coil_winder.JPG
• coils_and_magnet_placement.jpg
• coils_in_new_stator.jpg
• completed_drying_plate_mould_now_removing_paper.jpg
• conversion_program.exe
• cutting_fiberglass_2.JPG
• duct_tape_to_remove_metal_filings.jpg
• electrons_path.JPG
• electrons_path.bmp
• everybody_has_a_foreman__and_this_is_mine.jpg
• fiberglass_being_applied_to_stator.jpg
• fiberglass_resin__baby_powder__and_grease.jpg
• fiberglass_resin_and_baby_powder_used_for_stator_and_magnets.jpg
• finished_cell_hanging.jpg
• finished_panel.jpg
• genny_and_light.jpg
• genny_one.jpg
• hillbilly_coil_winder.jpg
• last_try_of_battery_wiring_12_volt.bmp
• lid_off_stator.jpg
• magnet_in_hand.jpg
• magnet_placement_jig_2.jpg
• magnet_placement_jig_completed.jpg
• magnets_in_resin_drying.jpg
• magnets_placed_on_rotor.jpg
• mags_on_plate_before_pouring_fiberglass.jpg
• makeshift_mould_for_pouring_fiberglass.jpg
• model_plane_wing_blade_balancer.JPG
• mold_curing.jpg
• mold_is_finished.jpg
• mold_with_lid_on_and_sander.jpg
• moose_at_montreal_river_property.jpg
• mundmill_flying_in_yard.jpg
• next_stator_to_be_made.jpg
• nice_wind_turbine_photo_may_05.jpg
• notice_light_when_turning_generator.jpg
• one_inch_dia_neos.jpg
• ouch_.JPG
• paint.bmp
• pic_at_campfire_summer_05.jpg
• points_of_balancer.JPG
• pythagorean_guy_wire_example.JPG
• rotor_for_17_ft_machine_with_mags.jpg
• rotor_primed.jpg
• rotors_for_17_ft_machine_resin_drying.jpg
• rotros_on_jack_screws_checking_alignment.jpg
• rubber_gloves_for_handling_fiberglass_resin.jpg
• solar_panel_test_3.jpg
• spindle_template.JPG
• stator_being_removed_from_mould.jpg
• stator_mixture_in_bud_light_pitcher.jpg
• stator_on_genny_bracket.jpg
• stator_out_of_mold_and__3_brass_fittings_added.jpg
• stator_template_20_inch.JPG
• supplies_used_in_stator_mixture.jpg
• tape_on_end_for_balance.JPG
• testing_3_panels.jpg
• three_brass_bolts_for_wiring.jpg
• three_phase_bridge_rectifiers_with_dielectric_grease.jpg
• transfer_punches.JPG
• wind_generator_frame.JPG
• windmill_1_air_shot
• windmill_on_a_sunny_day.jpg
• wings_encased_in_heat_shrink_plastic.JPG
• wires_attached_to_plug_for_easy_access.jpg
• zubbly_conversion__with_temp__pulley_wheel.jpg
• zubbly_conversion_with_new_plut_3_phase.jpg